Sign In | Join Free | My himfr.com
Home > Heat Shrinkable Sleeve >

PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line,

Qingdao Huashida Machinery Co., Ltd.
Trust Seal
Verified Supplier
Credit Check
Supplier Assessment
Contact Now
    Buy cheap PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line, from wholesalers
     
    Buy cheap PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line, from wholesalers
    • Buy cheap PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line, from wholesalers
    • Buy cheap PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line, from wholesalers
    • Buy cheap PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line, from wholesalers

    PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line,

    Ask Lasest Price
    Brand Name : HUASHIDA
    Certification : ISO
    Payment Terms : L/C, D/A, D/P, T/T, Western Union, MoneyGram
    Delivery Time : 10workdays
    • Product Details
    • Company Profile

    PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line,

    lightweight PE Heat Shrinkable Sleeve hot-melt method to connect,anticorrosive
    Wholesale pipe joint materials
    Heat Shrinkable Sleeve Insulation Connector


    1. HSSC-1 Heat shrinkable sleeve (2 layers), which are developed and manufacture by Qingdao Huashida machinery Co., Ltd for anti-corrosion of pipeline, are the composition of radiation cross-linked polyethylene backing and high shearing strengthen melt adhesive, and have the function of shape memory. The hot melt adhesive is squeezed into the joint by the shrink power to form a perfectly sealed surface, after being heated. HSSC-1 is compatible with standard pipe coating, also can be used for coating bare, replacement pipe section and large radius bends. The system is designed to be applied with minimum preheating and is ideal for large diameter wastewater pipe


    Application scope
    The heat shrinkable sleeve is designed to be applied with minimum preheating and is ideal for large diameter wastewater pipe. 3PE pipe and pre-insulated pipeline joint closure.

    ITEMStandardUNITData
    Adhesivesoftening pointASTM E 28°C70-80
    shear strengthDIN 30 672N/cm≥100
    Basicspecific densityASTM D792r/cm 30.935-0.96
    tensile strengthASTM D638Mpa15-20
    Elongation at breakASTM D792%350
    hardnessASTM D2240ball48
    Heat Shrinkable Sleevepeel strengthASTM D1000N/cm>150
    water-intake rateASTM D570%0.05





    Feature
    1.Fast shrinkage speed,
    2.good waterproof performance,
    3 good anti-corrosive performance,
    4.long service life, convenient transportation and fast construction.




    2. 3Layer Fiber

    reinforced PE heat shrinkable tape (sleeve) is composed of cross-linked polyethylene back, a middle layer of fiber and special heat melt adhesive an. The 3 layer reinforced sleeve gives better shrink ratio, and better strength. It is resistant to corrosion, wear, impact, UV and aging, easier to be operated.
    Application area:
    It is mainly used for Hollow wall spiral pipe, corrugated pipe and metal reinforced corrugated spiral pipe etc.

    TEST PROCEDURE
    1. Clean the steel pipe and heat it by fire till over 80 ºC
    2. Paint the steel pipe with Primer (mixed with A&B)
    3. Fire heat the heat shrink sleeve, be attention to start heating from middle of the sleeve, but act from up and down, and gradually move from middle to two sides of sleeve, in order to drive air out of the sleeve, after finish heating, the good result is that there is about 1-2mm hot adhesive melt at the edge of sleeve.

    Heat shrinkable Sleeve construction
    Before construction, scissors, flame spray gun, gas bottle, cleaning cloth, wire brush, protective gloves, shovel and other construction tools should be prepared.

    The surface of the pipe was preheated to improve the adhesive adhesion and the peeling strength of the pipe. The part of the pipe to be welded was preheated with a flame spray gun at a temperature of 50℃-60℃.

    After the pipe is preheated, move the shrink sleeve to the pipe interface to be welded. The shrink sleeve is centered at the center of the joint of the two pipes, and the margin on both sides is even.
    PE Heat Shrinkable Sleeve Wholesale Pipe Joint Materials
    PE Heat Shrinkable Sleeve Wholesale Pipe Joint Materials

    Huashida Machinery, with over 20 years' experience, is one of the professional oil gas 3pe pipeline girth welding coating heat shrink sleeve manufacturers in China. Offering the customized service, we warmly welcome you to get the high qualified products from our factory.
    Looking forward to cooperating with you.

    Quality PE Cross Linked PE Heat Shrinkable Sleeve Extruder Extrusion Line, for sale
    Inquiry Cart 0
    Send your message to this supplier
     
    *From:
    *To: Qingdao Huashida Machinery Co., Ltd.
    *Subject:
    *Message:
    Characters Remaining: (0/3000)